Galaxy Flex SMS notification via GSM-GPRS module

GALAXY FLEX SMS FORWARDING VIA GSM-GPRS MODULE ALSO THE NEW 4G Dialer
Galaxy Flex SMS forwarding via GSM-GPRS module

SMS forwarding via GSM

Step 1: Program the GSM/GPRS Module Configuration [menu 56.3.2] •
Select Network 1 [option 3]

Program the PLMN of the provider used [option 3.1] (See What is a PLMN at the bottom of this explanation and do I need to program it? Not NECESSARY for SMS forwarding only)

Program the phone number of the SMS Center of the provider used [option 3.5] see bottom of this page for details
Program the SIM PIN [option 6]

Step 2: Program the User Configuration [menu 56.2]

Program Mobile Number 1 [option 1]

Program Mobile Number 2 [option 2], if used
Program Mobile Number 3 [option 3], if used
Program the desired SMS Triggers [option 4]
Select the Mode for each desired trigger [option 4.x.2.1=enabled]
Program the Sequence for each desired trigger [option 4.x.3], for example [213]. For this trigger, the Galaxy Flex PBX will first attempt mobile number 2, then mobile number 1, and finally mobile number 3. Each number can be entered once in the cycle.

Program an SMS Site ID [option 5]. This is for identification of the PBX.
Advice: Program all phone numbers in international format (+316xxxxxxxxx). NOTE: This may vary per provider; sometimes this does not work, in which case only enter 06xxxxxxxx.

Note: A sequence must be set for each desired trigger; the order may differ per trigger.
Note: Go to the diagnostic menu [menu 61.1.06] and check for any errors of the GSM/GPRS module. Select the GSM/GPRS module and then one of the 3 sub-options [1=General, 2=GSM, 3=GPRS]

What is a PLMN and do I need to program it? PLMN stands for Public Land Mobile Network.
In every country, every mobile provider has its own PLMN to identify itself.
To force the GSM/GPRS module to use its own network, the PLMN of the SIM card provider must be entered. If the SIM is not placed in the country of origin, and therefore needs to roam, the SIM card can be used on most networks and one or more PLMNs, with corresponding provider details, must be entered.

Use a SIM card from KPN or Vodafone; these support the 2G network. OLD GSM Dialer, new one can also handle 4G. PLMN numbers of the Dutch providers

KPN Telecom 20408
Vodafone 20404

SMS center number:

KPN +31653131313
Vodafone +316540881000

Remotely switch on and off via an SMS message. The code 1234 is a fictitious code; you must use your own code. NOTE: USER CODE, then a space, and then the Command

SMS remote control
If the Flex PBX is equipped with a working GSM module, the user can control the system by sending a special SMS message to the phone number of the GSM. Please note that SMS control may not comply with the guidelines of EN50131.
SMS control must be enabled in menu 56.5.2.
Command format
The following commands can be sent to the PBX via SMS.

Query System Status: only the code. Example: query system status send an SMS with the following details 1234

Enable System I. Example: Fully enable the system send an SMS with the following details 1234 I
Partially secured In System D Enable partial security of the system send an SMS with the following details 1234 D
Disable System 1234 U Disable the system send an SMS with the following details 1234 U
The message must be sent to the phone number of the SIM card located in the
GSM module of the control panel.

Please note: if you wish to switch off the system remotely by sending an SMS message, take the following details into account.

The GSM card signal must be at least 40 to 45; otherwise, you can expect problems. Sending SMS is possible up to a signal strength of approximately 25, but the receiver works from a signal strength of approximately 35 to 40. This can be read in menu 61-6-ent-1-ent